profile - دانشکده فنی

 دانشکده فنی و مهندسی 

 پردیس دانشگاه رازی 
Mohsen Hayati

Mohsen Hayati

Professor / Engineering / Dept. of Electrical and Electronic Engineeingِِِ

Master Theses

  1. Design, simulation and fabrication of a microstrip low-pass filter using a modified Split Ring Resonator
    Behnam Vaisi 2026
       In this thesis a microstrip low-pass filter with a cutoff frequency of 2.4 GHz is designed using modified split-ring resonators. The proposed structure consists of a main transmission line two open-circuited stubs and two modified split-ring resonators. In the proposed resonator the outer ring features one gap while the inner ring features four gaps.       The filter is designed and fabricated on an FR4 substrate with a relative dielectric constant of ?r = 4.6 and a thickness of 1.6 mm. The overall dimensions of the structure are 29?97×18?86 mm . To analyze the electrical behavior of the structure, LC equivalent circuits were developed for the initial structure, the resonator, and the final structure; their responses were then compared with the results obtained from layout simulations.       Layout simulation results indicate that the filter's cutoff frequency at the -3 dB level is 3.318 GHz; the S11   lot remains below -20 dB up to approximately 1.5 GHz, and transmission zeros are located around 3.2 GHz, 3.6 GHz, and 5.0 GHz. Furthermore, measurement results confirmed the low-pass filter behavior and the transmission zeros, and the discrepancies relative to the layout simulation were analyzed.       Keywords:Microstrip Low-Pass Filter – Modified Split-Ring Resonator – Transmission Zero – Compact Dimensions – Stopband
  2. Electrical Modeling and L-I-V Characterization of Laser Diodes for Performance Optimization
    AHMED ABDULAMEER ASADKHAN 2026
       This thesis presents a comprehensive physics-based modeling and optimization study of 1550 nm InP/InGaAsP multiple quantum well (MQW) ridge-waveguide laser diodes for performance enhancement. The primary objective was to develop an accurate multi-physics model using Silvaco ATLAS Technology Computer-Aided Design (TCAD) software and to integrate it with the Particle Swarm Optimization (PSO) algorithm for systematic structural optimization. A baseline laser diode structure consisting of three compressively strained InGaAsP quantum wells embedded in a Separate Confinement Heterostructure (SCH) was designed and thoroughly characterized. The TCAD model incorporated advanced physical mechanisms, including strain-dependent band structure, Auger recombination, free-carrier and intervalence band absorption, thermionic emission with tunneling, and self-heating effects. After calibration against published experimental data, detailed Light-Current-Voltage (L-I-V) characterization and parametric sensitivity analysis were performed to identify the most influential design parameters. The PSO algorithm was subsequently coupled with the TCAD simulator to perform multi-objective optimization aimed at minimizing threshold current while maximizing slope efficiency and wall-plug efficiency, subject to thermal and wavelength constraints. After 80 iterations with a swarm of 30 particles, the optimized structure demonstrated significant performance improvements compared to the baseline design. The threshold current was reduced by 26.4% (from 18.2 mA to 13.4 mA), the slope efficiency increased by 17.4% (from 0.46 W/A to 0.54 W/A), and the peak wall-plug efficiency improved by 17.8%. The optimized device also exhibited higher output power and better thermal stability. The results confirm that the integration of rigorous TCAD-based device simulation with intelligent optimization algorithms provides an effective methodology for accelerating the design of high-performance long-wavelength laser diodes. This approach not only reduces development time and cost but also offers valuable physical insight into the relationships between structural parameters and device performance, contributing to the advancement of laser sources for optical communication systems. Abstract This thesis presents a comprehensive physics-based modeling and optimization study of 1550 nm InP/InGaAsP multiple quantum well (MQW) ridge-waveguide laser diodes for performance enhancement. The primary objective was to develop an accurate multi-physics model using Silvaco ATLAS Technology Computer-Aided Design (TCAD) software and to integrate it with the Particle Swarm Optimization (PSO) algorithm for systematic structural optimization. A baseline laser diode structure consisting of three compressively strained InGaAsP quantum wells embedded in a Separate Confinement Heterostructure (SCH) was designed and thoroughly characterized. The TCAD model incorporated advanced physical mechanisms, including strain-dependent band structure, Auger recombination, free-carrier and intervalence band absorption, thermionic emission with tunneling, and self-heating effects. After calibration against published experimental data, detailed Light-Current-Voltage (L-I-V) characterization and parametric sensitivity analysis were performed to identify the most influential design parameters.
  3. Design, simulation and fabrication of microstrip Wilkinson power divider using high and low impedance stubs
    Niloofar Asadi 2026
  4. Design and simulation of a compact dual-band branch-line coupler using modified interdigital capacitor
    Mahdi Mansouri 2025
       Abstract In this thesis, an innovative compact dual-band branch-line coupler is designed, simulated, and analyzed to operate efficiently at 2.24 GHz and 5 GHz. The primary objective of the thesis is to develop a miniaturized and low-loss microwave coupler capable of effectively suppressing higher-order harmonics, tailored for modern wireless communication systems such as 5G and advanced Wi-Fi networks. To achieve this, modern design techniques have been employed, including the use of a modified interdigital capacitor, a rectangular-shaped resonator for dual-band performance, and a custom-designed harmonic suppression cell. The proposed structure was simulated using ADS 2023, and results show outstanding performance. In the first band (2.24 GHz), the coupler achieves a coupling level of S21?=?0.13 dB and a return loss of S11?=?24.02 dB. In the second band (5 GHz), these values are -0.21 dB and below -20 dB, respectively. The fractional bandwidth (FBW) is measured to be 46% in the first band and 20% in the second. One of the most significant achievements of this work is the suppression of harmonics up to the seventh order, alongside a remarkable reduction in physical size to just 0.0154?g2 . The circuit was fabricated on a Rogers 5880 substrate and tested at the Computational Intelligence Laboratory of Razi University, Kermanshah. The experimental measurements closely match the simulation results, confirming the stability and reliability of the design. Given its unique features, the proposed coupler is a strong candidate for integration into compact, multi-band, and next-generation RF systems. Keywords: Branch-line coupler, dual-band structure, modified interdigital capacitor, fractional bandwidth, microstrip lines, 5G systems
  5. Design, Simulation, and Fabrication of a Power Divider Using Resonators with Combined Modified Circles and Stubs
    Mohammad amin Masoumi 2025
    Given the increasing need for compact, high-performance passive devices with harmonic suppression capability in modern telecommunication systems, this thesis addresses the design of a compact Wilkinson power divider using modified resonator structures. The main objective is to reduce size, improve bandwidth, and effectively eliminate harmonics. The proposed design is implemented on a Rogers RT/duroid 5880 substrate with a thickness of 25 mil and operates at a center frequency of 2 GHz. Results demonstrate a significant size reduction of 86% compared to the conventional design, a wide fractional bandwidth of 65%, and effective suppression of 6 harmonics (2nd to 7th order). Electrical performance at 2 GHz includes return loss better than 26 dB, insertion loss approximately 3.031 dB, and isolation better than 20 dB. The total physical dimensions are only 0.078?g?×0.11?g?. This power divider, offering compact dimensions, wide bandwidth, and harmonic suppression capability, is considered an ideal option for modern high-density RF/microwave systems.
  6. Design and fabrication of Wilkinson power divider with harmonic elimination capability using modified circular resonators and meandered lines.
    SAJAD IMANI BADERBANI 2025
       The Wilkinson power divider is a key component in the design of RF and microwave circuits, used to split the input power into multiple outputs while maintaining impedance matching and high efficiency. The importance of designing a Wilkinson power divider lies in its ability to not only effectively divide power but also address the need for isolation between output ports and reduce return losses. These features make the Wilkinson power divider widely used in many communication, radar, and other RF applications that require precise and reliable performance. Proper design of this divider can lead to improved system efficiency and reduced signal interference across different frequencies.
  7. Diagnosis of heart diseases utilizing machine learning algorithms
    Nesa Amiri 2025
       Cardiovascular diseases, particularly arrhythmias, have been among the leading causes of mortality in recent years. Consequently, the medical community has been actively seeking efficient and rapid methods for diagnosing these conditions. To enhance diagnostic speed and minimize potential human errors, the use of automated methods for detecting arrhythmias has gained significant attention. This study aims to achieve accurate and timely detection of various arrhythmias with minimal computational complexity and a reduced number of features. in this thesis, three types of arrhythmias—atrial, sinus, and ventricular—are analyzed, with each category comprising 100 ECG signal samples sourced from the SHEDB database. Two models, the Multilayer Perceptron (MLP) neural network and the Radial Basis Function (RBF) neural network, were employed for arrhythmia classification. Results indicate that the MLP model, achieving a test accuracy of 97.8%, significantly outperformed the RBF model, which achieved a test accuracy of 76.7%. These models were selected to reduce computational overhead compared to more complex models like Convolutional Neural Networks (C  ). furthermore, various temporal, statistical, and frequency domain features were examined during the feature extraction process. The best performance was achieved using eight selected features: Root Mean Square (RMS), Waveform Length (WL), Absolute Sum of Squares( ASS), Mean (MEAN), Skewness (SKW), Kurtosis (KUR), Dominant Frequency (DF), and Amplitude of Dominant Frequency (AFDF).
  8. Prediction of diabetes using machine learning algorithms
    Sina Alimoradi 2025
      Diabetes mellitus is a chronic metabolic disease characterized by the body's inability to effectively use blood sugar or produce sufficient insulin to regulate it. If not properly diagnosed and treated, this disease can lead to serious complications such as heart disease, kidney damage, nerve disorders, and blindness. Given the increasing global prevalence of diabetes, early identification and prediction of this disease is of paramount importance. This research focuses on predicting the onset of diabetes using machine learning algorithms. For this purpose, the Pima Indian Diabetes dataset is employed, which includes features such as age, weight, blood pressure, fasting blood glucose levels, Body Mass Index (BMI), number of pregnancies, family history of diabetes, and other biological parameters. These data, extracted from a population of Native American women, are used to train and test various machine-learning models. In this study, different algorithms including Logistic Regression, XGBoost, AdaBoost, LightGBM, Decision Tree, CatBoost, and Gradient Boosting, were employed to predict the onset of diabetes. The results of this research, which compares different algorithms, particularly boosting algorithms, indicate that some of these algorithms demonstrate higher accuracy in predicting diabetes and can be used as effective tools for early detection and optimal management of the disease. The models achieved the following accuracy: Logistic Regression (0.92), XGBoost (0.96), AdaBoost (0.94), LightGBM (0.96), Gradient Boosting (0.91), and Decision Tree (0.91), with the best performance achieved by CatBoost with an accuracy of 0.98. Finally, suggestions for future research are offered.
  9. Design, simulation and fabrication of a compact Gysel power divider with hybrid structure and wide bandwidth
    Hossien Mohamadi 2024
       This thesis presents the investigation, design, simulation, and fabrication of a compact Gysel power divider with a hybrid structure and wide pa  and. The primary objective of this research is to enhance the performance and reduce the size of the Gysel power divider by employing novel resonators and lumped elements. Rectangular and hairpin resonators were designed to create transmission zeros and improve impedance matching. These resonators are capable of generating six transmission zeros in their stopband, significantly improving filtering performance and unwanted frequency suppression. The circuit implementation utilized a substrate with the specifications of Rogers RT/Duroid 5880. The initial simulations of this circuit were conducted using the Advanced Design System (ADS) software. Simulation results indicated that the designed circuit exhibits very low return loss (S11) and adequate power transmission (S21) at the frequencies of 8.74 GHz and 9.23 GHz. Specifically, at these frequencies, S21 was measured to be -3.08 dB and -3.1 dB, respectively, while the return loss (S11) was -22.3 dB and -20.8 dB, respectively. Furthermore, the isolation (S32) was found to be less than -25 dB, demonstrating good signal separation between ports. These simulation and measurement results show good agreement and confirm the optimal performance of the circuit. Following the simulation phase, the designed Gysel power divider was practically fabricated and tested. The fabrication process included preparing the printed circuit board (PCB) mask, exposing and etching the board, and soldering the lumped elements. The practical measurement results closely matched the simulation results, validating the circuit's optimal performance in real-world conditions. One significant achievement of this research is the reduction of the circuit's size by 86% compared to the initial structure, highlighting a considerable advancement in circuit design and optimization. This dual-band power divider, with its optimized design and compact size, is suitable for various telecommunications, radar, and electronic systems that require precise and efficient power division. Recommendations for future work include further optimization of the pa  and width, the use of new materials with better dielectric properties, and examining the environmental and thermal effects on the circuit's performance. These advancements can further develop and enhance the technology of power dividers, improving the efficiency of telecommunications and radar systems. Given the results obtained, it is anticipated that these optimization and design methods will continue to be of interest and lead to further improvements in telecommunications and electronic equipment. This research offers an innovative and efficient solution, marking a significant step forward in developing advanced technologies in the field of telecommunications and electronics.
  10. Design of miniaturized ultra-wide stopband low pass-band pass diplexer using hexagon-shaped resonators
    Alireza Zarghami 2024
    In this research, a lowpass-bandpass diplexer with ultra-wide stopband and low insertion loss using hexagon-shaped resonators. The proposed diplexer consists of a bandpass (BPF) and a lowpass filter (LPF), representing the core concept of the proposed design method that aims to concurrently design BPF and LPF. In this proposed design method, the influence of the LPF filter on the BPF's design has been identified through coupling matrix analysis for the first time. Initially, an LPF is designed based on three coupled hexagon-shaped elliptical resonators. Subsequently, a novel model for BPF design, utilizing coupled high-impedance lines, has been introduced. Following this, the BPF model is developed using coupling matrix analysis while considering the impact of LPF resonators. The LPF have a 1.32 GHz cut-off frequency and ultra-wide stopband up to 17.42 GHz. The BPF consisted of four resonators and the hexagon-shaped structure is used instead of low impedance lines. The utilization of hexagon-shaped resonators serves the purpose of enhancing the precision of the coupling effect, aligning with the proposed coupling matrix analysis. Additionally, hexagon-shaped resonators exhibit a greater capacitive effect, leading to a reduction in insertion loss within the pa  and when compared to rectangular-shaped resonators. The BPF has narrow pa  and with center frequency of is 2.25 GHz and 0.31 GHz bandwidth. The measured insertion losses of LPF and BPF are less than 0.75 dB and 0.81 dB, respectively in 60% of pa  ands
  11. Design, simulation and fabrication of Wilkinson power divider usin modified elliptic resonator
    Narjes Dast Dadeh 2023
  12. Design, Simulation and fabrication of compact Wilkinson power divider with harmonics suppression using combination of Chebyshev and modified elliptic structure
    Mina Saran 2023
      In
  13. Design,simulation and fabrication of Gysel power divider using radial and modified T-shaped resonators
    Mohsen Eghbalkhah 2023
       Due to the growth of the use of electronic devices such as electronic amplifiers, wireless devices, etc., power dividers have gained special importance, and the most important of these dividers are Wilkinson and Gysel, which are widely used. take The main task of dividers in the electronic circuit is power division, which is evaluated in symmetrical and asymmetrical divider models today.    The problem discussed in this thesis is to pay attention to the reduction of the physical size that affects the size of the electric circuit, that the reduction of the designed dividers reduces the dimensions of the circuit. It increases the quality of the output wave and also increases the conduction bandwidth, which plays a significant role in the selection of dividers in devices, which is investigated using microstrip technology today. In this thesis, ADS software has been used to simulate a Gysel divider, which has been obtained by reducing the dimensions, removing additional harmonics, and providing proper isolation, and good results have been obtained.
  14. Design, simulation and fabrication of Narrow-band Wilkinson power divider based on the new bandpass structure and Elliptic resonators
    Zeinab Razeghi 2023
  15. Design and simulation of narrowband low-noise amplifier using forward body bias and noise cancellation techniques.
    Reza Mohammadi 2023
       In recent decades, due to the growth and development of mobile telecommunication equipment and portable systems, RF researchers and designers have focused more on designing circuits with low voltage and power consumption. Most systems are now wireless, and reducing power consumption is important, which can lead to increased battery life. One of the important parts in receiver systems is the low-noise amplifier, which should be designed with low power. In this thesis, a narrowband low noise amplifier with low energy consumption and high voltage gain is presented using 0.18 ?m RF CMOS technology, so that in the proposed amplifier, the threshold voltage of the transistor can be reduced from the bias technique. body and to reduce the supply voltage and current, current reuse technique has been used. Due to the use of noise removal technique in the proposed circuit, it has resulted in acceptable noise reduction, and with the appropriate selection of circuit elements, a compromise between circuit parameters has been created. The results of the investigations show that the gain of the proposed low-noise amplifier is 13.8 dB, S11 is less than -14.37 dB, and the noise figure is 2 dB at the central frequency of 2.4 GHz. Also, the linearity is -2.5 dBm and the power consumption at the power supply voltage of 1 V is 3.79 milliwatts. The use of such a circuit can greatly contribute to the design of low-power, high-performance wireless communication systems. With further modifications, it can also be used in IoT applications where low power consumption is critical. Overall, this work shows a promising trend for the development of compact, low-power and efficient amplifiers using advanced RF CMOS technologies.
  16. Design, simulation and fabrication of Wilkinson power divider with harmonic suppression and size reduction using T and triangular shaped resonators.
    Ehsan Bidarian 2023
  17. بهبود راندمان سلول هاي خورشيدي با استفاده از پديده پلاسمونيك
    Zahra Zand 2023
  18. Design and fabrication of Wilkinson power divider with small dimensions and extensive suppression of harmonics using the modified rectangular resonator
    Saeid Ahmadi 2022
    Microstrip lines are good candidates for designing microwave filters, power amplifiers, inventors. With other elements of microwave circuits on a circuit board, he pointed out. Other applications of microstrip lines include waveguides, oscillators, and microwave power dividers.  
  19. Design, Simulation and fabrication of compact Wilkinson power divider with high harmonic suppression using rectangular resonators and curved transmission lines
    Fatemeh Mirzaee 2022
  20. Predicting ultimate bearing capacity of shallow foundations in Kermanshah city using artificial neural network
    Hadis Nori 2022
  21. Diagnosis of muscular motion diseases using surface EMG signal by deep learning method
    Hosna Tirandaz 2022
      Electromyography (EMG) is a widely used diagnostic tool in clinical physiology which is used by physicians to accurately diagnose neuromuscular disorders in patients, particularly myopathy. In this research, continuous wavelet transform method and convolutional neural network were used to diagnose myopathy from EMG signals. The data analyzed in this study included two groups of healthy (20 signals) and myopathy (44 signals). The continuous wavelet transform was performed to decompose each signal after preprocessing operations on them. Then the scalogram was extracted and used as an input image to the convolutional neural network. The neural network structure used in this research composed seven layers which were taught by 70% of the total data. The final accuracy of this model in detecting myopathy from EMG signal was 89.06%.
  22. Classification of electroencephalographic signals for hand movement detection in the form of a deep learning approach
    Mahya Nikooei 2022
      امروزه با افزايش ارتباط بين فناوريهاي رايانهاي و حوزه پزشكي، واسطهاي مغز و كامپيوترتأثير مهمي در زمينههاي مختلف از جمله تشخيص فعاليت تصور حركت، بازشناسي احساسات، تشخيص بيماري صرع، امتياز بندي سطح خواب و باركاري ذهني دارند. تشخيص تصور حركت يكي از تكنيكهاي مبتني بر واسط مغز و كامپيوتر است. اين تكنولوژي با پردازش سيگنالهاي مغز و استخراج الگو از يكي از مهمترين سيگنالها در تشخيص اين نوع EEG تأثير به سزايي بر مطالعه ذهن وكاركردهاي آن دارد. سيگنال ،MI سيگنالهاي فعاليت است. اين پژوهش به طراحي، پياده سازي و ارزيابي يك روش جديد براي تشخيص تصور حزكت دست انسان مي پردازد. مغز انسان اين قابليت را دارد كه از طريق ارتباط بين نواحي و اثرگذاري بر يكديگر منجر به فعاليت هاي شناختي شود. به عبارت ديگر مغز از نواحي مختلفي تشكيل شده است كه هر كدام از آن ها يا به طور جداگانه يا تعاملي منجر به اجراي وظايف مختلف توسط انسان مي شود. اين روش جديد، از قابليت ذكر شده جهت ارزيابي عملكرد مغز و تشخيص تصور حركت دست انسان استفاده كرده است. در اين تحقيق تلاش شده است كه اطلاعات دقيق تر و كامل تري جهت ارزيابي مدل پيشنهادي، استفاده شود. به اين منظور براي تحليل سيگنال هاي حاصل از تصور حركت، از رويكرد مسئله معكوس به كار برده شد كه به اطلاعات آناتوميكي مغز حين تصور حركت دست EEG دسترسي دارد. در اين راستا از بازسازي منبع سه بعدي كه شامل مراحل مدل سازي فضاي منبع، مدل پيشرو و مسئله معكوس است، به كار برده شد. باتوجه به اطلاعات به دست آمده، از اتصال مؤثر (يكي از سه نوع اتصال بين نواحي مغز) مبتني بر مدل سازي علّي پويا استفاده گرديد كه گراف مربوط به نواحي مرتبط با تصور حركت طراحي و پياده سازي شود. نواحي مؤثر به كمك بازسازي منبع به دست آمده است. اين نوع مدل سازي بهتر مي تواند اتصالات جهت دار و علّي بين نواحي مغز و نقش مؤثر فعاليت نورون هاي قشر مغز را در ايجاد و اجراي تصور حركت تفسير كند. به دليل اينكه اطلاعات حاصل از گراف مدل سازي علّي پويا يك ماتريس مجاورت از مقادير اتصال مؤثر بين نواحي، ناشي از تعامل و اثر گذاري قشرهاي مغز است براي سهولت در استخراج ويژگي هاي سطح بالاي تصور حركت، از تكنيك شبكه عصبي كانولوشن گراف گونه جهت طبقه بندي نوع تصور حركت به كار برده شد. اين شبكه عصبي از طريق ماتريس مجاورت، جهت بين نواحي را تشخيص مي دهد و اطلاعات يال و رئوس گراف را براي استخراج ويژگي به كار مي برد. نتايج اين روش دقت بالاتري را در مقايسه با 5 و 10 لايه جهت تشخيص (GCN_ نشان داده است كه اجراي شبكه عصبي با 15 لايه ي كانولوشني ( 15 0% است. در مقايسه با / 0% و 99 / نوع تصور حركت را داشته است. دقت حاصل براي تصور حركت دست راست و چپ به ترتيب 95 پژوهش هاي پيشين نيز، روش پيشنهادي توانسته است دقت تشخيص را افزايش دهد.
  23. Design and fabrication of Wilkinson power divider with harmonics suppression using symmetrical rectangular resonator
    Behrouz Routabi 2022
    Design and fabrication of Wilkinson power divider with harmonics suppression using symmetrical rectangular resonator  
  24. ارزيابي مقاومت تيرهاي عميق بتن مسلح بر اساس مدل STM با استفاده از شبكه عصبي مصنوعي
    Arman Haiati 2022
       Deep beams as the most important bending-shear member are widely used in a variety of structural and non-structural structures. The cross-sectional height of these beams is higher than that of ordinary beams, so that according to the American Concrete Code, in deep beams, the cross-sectional height is greater than four times the length of the span. Analysis and design methods in deep reinforced concrete beams differ from ordinary beams due to their unique properties. Closing method is one of the most common methods in the analysis and design of deep beams. In this research, the mentioned method as one of the main topics was reviewed and some examples of existing experimental models were analyzed and evaluated. In order to study the details of the mentioned model, 432 laboratory samples with simple support and concrete efficiency coefficient were collected and examined from the laboratory researches carried out in recent years, considering the effect of reinforcing reinforcements where the total shear force applied to the beam is borne by two independent supports. The most important purpose of this study is to provide a formula for predicting shear strength by considering all effective factors. To achieve the project goal, numerical studies based on artificial intelligence were performed. Artificial intelligence is a computational method that tries to mimic human cognitive ability in a very simple way to solve engineering problems that have disregarded common computational techniques. Next, according to the experimental results, a new fastening model that included a wide range of deep beams with different arrangements of shear reinforcement, concrete strength and effective shear-height ratio was investigated. In this study, the shear capacity of deep beam specimens that have been tested by different people so far was calculated and the results were compared with the actual values ??and results of several other existing bonding methods. The results of the comparison indicate the satisfactory accuracy and efficiency of the proposed model. The proposed method is able to predict the shear strength of simple deep beams with acceptable accuracy.
  25. Application of Deep learning to Identification disease by FNIRS
    Neda Beygi mirazizi 2021
  26. Design Of UWB-LNA and Noise Cancelling Usign Current Reuse
    Reza Mohammadi norouzabadi 2021
       Abstract: this paper presents a technique for low noise figure reduction of low-noise-amplifier. The proposed LNA is designed in a current reuse technique that offers lower noise figure. Also, using inductor as a gate inductor reduces the effect of the input parasitic capacitance on the noise figure and provides a good matching at the input and output of the LNA. It shows that the proposed technique reduces significantly the noise figure and improves the matching. The proposed LNA is designed in 0.18 ?m process with 1.5 V supply voltage and simulated cadence software. The simulation results show that The LNA achieves voltage gain of 13.3 dB, noise figure of 2.3 dB, and S11 less than ?10 dB, while consuming only 8.1   mW. The layout schematic occupies 0.812 of chip area.
  27. nd Fabrication of Dual-band power divider Willkinson using low and high stubs
    Mehran Bahrambeigi 2021
    در اين پايان نامه، يك تقسيم كننده توان ويلكينسون ارائه شده است. كه در ان علاوه بر دارا بودن دو باند كاري داراي حذف هارمونيك نيز مي باشد. اين تقسيم كننده با كمك رزناتتورهاي متقارن و استاب هاي بلند و كوتاه طراحي شده است.اولين فركانس كاري اين (WPD) در فركانس 2GHz مي باشد و دومين فركانس كاري 14/1GHz مي باشد و اندازه اين كار   مي باشد لازم به ذكر است كه حذف هارمونيك و تقسيم كننده بسيار مهم است كه در اين تقسيم كننده 5 هارمونيك حذف شده است.اين تقسيم كننده بر روي برد RT-5880 ساخته و اندازه گيري شده است جواب ساخت و شبيه سازي تطبيق مناسبي دارند.
  28. Design of Tunable Band Stop Metal-Insulator-Metal Plasmonic Filter in Near Infrared Band based on T Resonators
    Mahdi Kamari 2021
  29. Design of ultra wide band low noise amplifier with noises canceling technique with capacitive feeder network
    Hossein Khodarahmi 2021
  30. Design and Fabrication of Wilkinson power divider with small dimensions and extensive Suppression of harmonics using combination of trapezoidal,circular and square resonators
    Mohammad sajad Imani 2021
    In this thesis, a new structure WPD with a combination of trapezoidal, circular and rectangular resonators is presented, which has small dimensions of about 11.66 mm× 13.9 mm (0.1 ?g × 0.08 ?g). It also rejects unwanted harmonics from 3.2 to 17 GHz, which means up to 10fo. The operation frequency is located at 1.67 GHz. Other benefits of proposed PD include good FBW (138%) and return losses (-28 dB). Also, the even and odd-mode analysis with LC equivalent circuit and ABCD matrix has been employed to assess the behaviour of the proposed WPD. There is a good agreement between measurements and simulation results. Thus, the proposed Wilkinson power divider can be utilized in various microwave circuits and systems.  
  31. Compact Microstrip Lowpass Filter With Wide and High Attenuation Stop band, Sharp Roll-off and Low Insertion Loss
    Saber Farhangian 2020
  32. Energy Management in A Multi-agent-microgrids
    Farhood Ghalkhani 2020
  33. Design, Simulation and fabrication of Wilkinson Power Divider with compact size and parameters improvment
    Sonia Asadi 2020
      Design, simulation and fabrication of Wilkinson Power Divider with compact size and improvement parameters Thesis Title:
  34. design, simulation and fabrication of microstrip lowpass filter using modified trapezoidal resonator
    Kambiz Yazdani 2019
  35. Development of Optimal Water Supply Plan Using Integrated Fuzzy Multi Criteria Decision-Making Methods – Case Study of the Gamasiab Basin in Kermanshah Province
    Amir Noori 2019
    This thesis presents a novel method for thedevelopment of an optimal water supply plan showcased using data from the Gamasiab basin, located in Kermanshah province, Iran, concerning new dams that are being constructed in this semi-arid region. In this research, a new group multi-criteria decision-making [MCDM] plan is proposed by combining two MCDM methods based on the Fuzzy Delphi and Fuzzy ELECTRE III methods that convert the experts’ opinions to triangular fuzzy numbers TFNs] based on the level of uncertainty associated with various quantitative] and qualitative criteria. Considering the opinions of non-stakeholders and data analysis using the Fuzzy Delphi method, the criteria were evaluated. Then, by analyzing the results using the Fuzzy ELECTRE III method, the final ranking of scenarios is obtained. A sensitivity analysis was conducted to assess the effect of uncertainty on the performance of the decision-making [DM] system in scenarios ranking. To calculate the importance weight of criteria, Expert choice software and empirical method were used. In addition, a hierarchical model based geographic information system [GIS] and Analytic Hierarchy Process [AHP] was used to determine the importance weight of quantitative criteria. Then, by comparing the result of GIS-based model with the quantitative criteria weight obtained from two other ones, it was found the importance weight of the criteria in the GIS-based hierarchical model due to the high ability to store and integrate information layers, has a higher value. Furthermore, the total expense criteria, the environmental impacts, transmission and water diversion, and geographical conditions of the region played significant role in selecting the optimal scenario. Additionally, the result of a WEAP model was used to evaluate the performance of the optimal scenario in terms of hydrological parameters. The data indicated that there was a good agreement between the results obtained from the hydrological model and the scenario ranking by employed method. Altogether, comparison of the proposed method with other MCDM methods, including Fuzzy AHP and .Fuzzy TOPSIS, indicated that the results of the employed method matched more closely to the local experts’ opinion. Keywords: Optimal Water supply, Gamasiab basin, Group Decision-Making, Fuzzy Delphi, Fuzzy ELECTRE III, Triangular fuzzy number, GIS
  36. Design and simulation of LNA in 2.4GHz with Feedback Linearity Technique for Wi-Fi Application
    Saeideh Bahrehbar 2019
  37. Design & Simulation of UWB LNA using HYBRID PD-DS Linearity Technique
    SERVEH RAHIMI 2019
  38. طراحي و شبيه سازي تقويت كننده كم نويز پهن باند با اولويت دادن به پارامترهايي مانند توان مصرفي، بهره، نويز فيگر و تلفات بازگشتي
    Farshad Mohammadsadeghi 2019
  39. Design, Simulation and Fabrication of Wilkinson Power Divider Using Modified Triangular with compact size and harmonic suppression
    Seyed Aabed Zonouri 2019
  40. طراحي، شبيه سازي و ساخت فيلتر مايكرواستريپ پايين گذر با استفاده از تضعيف گر استوانه اي و رزناتورهاي دايره اي اصلاح شده
    Shoeib Mohammadi nor 2018
      AbstractWith attention to the development of new sciences, in particular electronic science and telecommunication, radio waves (radio communications), the size and physical size of high-capacity components will be smaller and smaller in integrated circuits, and these changes also affect the unwanted (noise) signals in the structure. As a result, we need high-performance filters to eliminate these unwanted waves. There are many errors in the integrated circuits due to the high frequencies, and also have unusual dimensions and size. Using the microstrip technique is very suitable for using a substrate (dielectric) substrate. For use in microwave integrated circuit circuits. In this dissertation, a low-pass microprocessor filter with very small size, a wide bandwidth and good return loss are presented.After designing and using the ADS (Advanced Design System) software and comparing the simulated and measured results, the values are acceptable.
  41. طراحي و شبيه سازي تقويت كننده كم نويز در باند فرا پهن با استفاده از تكنيك هاي استفاده دوباره از جريان و حذف نويز جديد براي كاربردهاي باند پهن
    Malek Sharifi 2018
     B
  42. طراحي شبيه سازي وساخت فيلتر مايكرواستريپ پايين گذر با استفاده از رزوناتورمستطيلي وبارگذاري شده با استاب امپدانس بالا
    Seyed hamed Kazemi 2018
    a
  43. طراحي تقويت كننده كم نويز با تكنيك هاي برهم نهي مشتق اصلاح شده و استفاده مجدد از جريان
    Mohsen Alinia 2018
    Today, the use of wireless technology has become very popular It has become an indelible part of everyday life and even the industry And an example of its applications can be cell phones, WiFi networks, Radio digital information exchange and more Cited.   To achieve these technologies, various engineering knowledge and achievements, especially in the field of electronic, have been used. Providing these features on a small chip in the advancement of the science of minimizing components VLSI , CMOS technology And the construction of RF components and circuits It's possible; RF design includes parts such as antennas, low noise amplifiers,mixers, oscillators, phase lock loops, frequency instruments and power amplifiers.An important part of the network after the antenna is the low noise amplifier, which has various parameters that interact with each other. Including noise, bandwidth, linearity, input matching and extra ; We have tried to get a more linear response from the circuit using the Linearity enhancement techniques and we have achieved 3.1-10.6 GHz bandwidth. The proposed circuit structure in the fourth chapter of this thesis is examined.key words:Low noise amplifier, bandwidth, linearity, gain, linearization technique
  44. Design and Analysis of Class-E Power Amplifier under sub–nominal Condition.
    Seyed maziar Shahebrahimi 2018
  45. Design of Ultra-Wide-Band Low Noise Amplifier Using Modified Complementary Current-Reused technique
    Babak Salimi 2018
    طراحي تقويت كننده كم نويز در باند فركانسي فوق وسيع با استفاده از تكنيك استفاده مجدد جريان مكمل اصلاح شده
  46. Design of Compact Dual-Band Bandpass Filter With Simple Structure Using Square Resonator
    Golnaz Amini 2018
  47. طراحي و ساخت فيلتر پايين گذر با استفاده از رزوناتور تي شكل اصلاح شده و خطوط مارپيچ
    Mohamadghasem Kordi peykani 2018
    در اين پايان نامه به كمك رزوناتورهايTشكل ونيمدايره اي يك فيلتر پايين گذر طراحي، شبيه سازي و ساخته شده است. اين فيلتر داراي فركانس قطع GHz34/1است و همچنين تيزي آن از سطح dB3 تا dB40 برابر GHz41/0 است. همچنين باند قطع اين ساختار از فركانس GHz68/1 تا GHz20 مي­باشد كه نشان مي­دهد فيلتري با پهناي باند قطع عريض طراحي شده است و سطح حذف هارمونيك در باند قطع اين فيلتر برابر dB20 است. اندازه اين فيلتر برابر 9mm2/15 ×3/9مي­باشد كه با اين خصوصيات، اين فيلتر از ضريب شايستگي67954 بهره مي­برد. لازم به ذكر مي باشد كه در اين پايان نامه، فيلتر پايين گذر طراحي شده به چند رزوناتور   تقسيم شده و اين فيلتر ساخته شده است كه مشاهده مي شود پاسخ ساخت و شبيه سازي تطبيق خيلي مناسبي مي­باشند.  كلمات كليدي:رزوناتور،­فيلتر پايين گذر، اندازه كوچك، فركانس قطع.
  48. Design and Fabrication of Microstrip Band pass Filter Using Square Open loop Resonator
    Ali Amiri 2017
  49. Desing simulation and Fabrication of Compact Microstrip Low Pass Filter Using Modified Circular Resonator
    Abbas Piri 2017
  50. design of high gain LNA for bluetooth Application
    Zahra Shasavari 2017
    desing of high gain LNA for bluetooth Application
  51. Wilkinson Power Divider using Low Pass Filter with compact size and Harmonics Suppression
    Foroozan Ghaderzadeh 2017
      Wilkinson Power Divider using Low Pass Filter with compact size and Harmonics Suppression
  52. Design of an ultra-wideband low noise amplifier with desirable linearity
    Maryam Akbari 2017
    Design of an ultra-wideband low noise amplifier with desirable linearity
  53. Design of an ultra-wideband low noise amplifier with low power
    Rezvan Salahi 2017
  54. Design of Compact Quad-Band Bandpass Filter with Simple Structure and Controllable Frequencies Using Single Rectangular Ring Resonator
    2017
      Design of Compact Quad-Band Bandpass Filter with Simple Structure and Controllable Frequencies Using Single Rectangular Ring Resonator
  55. Design, Simulation and Fabrication of microstrip ultra- wide band (UWB) band pass filter (BPP) with triple notched using stepped impedance resonator.
    Milad Kanjoriyan 2017
    Design, Simulation and Fabrication of microstrip ultra- wide band (UWB) band pass filter (BPF) with triple notched using stepped impedance resonator.
  56. Design of LNA with wideband
    2017
  57. design simulation and fabrication of compact microstrip lowpass filter with wide stopband using modified rectangular resonator loaded by stub
    Fateme Azimi fashi 2017
    Compact ultra-wide stopband lowpassfilter using modified rectangular resonatorloaded by stub  
  58. design of very compact microstrip Bandpass filter with high - selectivity for X-&ku-band applications
    Ali Nargesi Khojasteh 2017
      In this thesis two new compact size high selective microstrip bandpass filters for X- and Ku-band are proposed. The presented structure uses T-shaped resonators with direct connected orthogonal feed lines. The T-shaped resonator provides high selectivity for the proposed filter and reduces the overall size of the filter, compared with conventional uniform stub. Due to its symmetrical structures, it can be analysed with the odd and even mode. Two filters at X- and Ku-band, respectively with fractional bandwidth of 30.3 % and 37 % were realized on a Roger 5880 substrate with dielectric constant of 2.2 and 15mil thickness. Simulation and experimental results demonstrate good agreement.
  59. Design of compact class-F power amplifier with high efficiency and output power
    Sepehr Zarghami 2016
  60. Design and fabrication of a microstrip lowpass filter using tetramerous radial stubs resonator
    Salma Ali sadeq 2016
  61. Design and fabrication of microstrip lowpass filter using modified ring resonator
    Sajjad Mohanad mustafa 2016
  62. design of low noise amplifier using noise-canceling technique
    SAJAD CHERAGHALIEI 2016
  63. design optimization and fabrication of microstrip low pass filter using modified traingle resonators
    2016
  64. design of oltra-WIDEBAND low noise amplifire with high linearity
    Mohsen Alirezapoor 2016
  65. Design of wilkinson power divider using hairpin resonator
    MOHAMADSAEED DOREYATIM 2015
  66. Design of microdtrip lowpass filter with proper roll off & bandwidth
    Fereshte Lorestani 2015
  67. Modeling of microstrip low pass filter using artificial neural network
    Yasaman Abedini 2015
  68. design of microstrip low pass filter using split ring resonators
    Saba Ebrahimpanah 2015
  69. Design of compact microstrip low pass filter with sharp roll- off and wide- stopband
    Ali Niazi 2015
  70. Design, optimization and fabrication of microstrip low pass filter using sqare resonators
    2015
  71. Design & fabrication of the microstrip lowpass filter using modified rhombic & radial shaped resonator for application in communication systems
    Mehrnaz Khodadoost 2015
  72. Design of microstrip lowpass filter using high- low Impedance stubs
    Farzad 2015
  73. Design and fabrication of hybrid coupler with small size using T and stucture
    Elham Shetabi 2015
  74. Design of Band Low Noise amplifire
    SIAMAK VEISI 2014
  75. design and optimization of the couplerusing bended structure
    Mahin Ehteshami 2013
  76. design and fabrication of microstrip low-pass filter using
    Zahra Faramarzi 2013
  77. aminiaturized wilkinson power divider with nth harmonic suppression using hight-low impedance resonator cells
    Ashkan Abdipour 2013
  78. desigining and fabrication of a novel compact microstrip low pass filter with wide rejection band and sharp ferquency response using diamond resonator
    Mozhgan Amiri 2013
  79. Desinning, optimization and fabrication of microstrip low-pass filter using butterfly shaped resonator
    2012
  80. design optimization and fabrication of microstrip low-pass filter using triangular resonator
    2012
  81. Design, Optimization and Fabrication of microstrip Low- pass Filter U sing Semicicle Ended Stub Resonator to operate at rader frequencies and filtering at microwavefrequencies
    2012
  82. Designing , optimization and Fabrication of Steped - impedance LOw Pass Filter using T- shape Step Impedance Microstip resonatos
    Hamed Abbasi 2012
  83. design ,optimization and fabrication of a compact wide-stopband low-pass filter using series hairpin resonartor
    2012
  84. investigation and prediction of the effect of nanofluids on efficiency of flat plate solar collectors with artificial neural network
    2012
  85. design and fabrication of microstrip bandpass trisection filter with 2 GHZ center frequency using SIR resonators for multiple spurious suppression
    2011
  86. design optimization and fabrication of low- pass filter using trapezoidal microstrip resonator
    2011
  87. design,optimization and fabrication of microstrip low-pass filter using radial stubs for filtering at microwave frequency
    2011
  88. design optimization and fabrication of microstrip low-pass filter using simple u-shaped resonators
    FARZIN SHAMA 2011
  89. design ,optimization and fabrication of microstrip low-pas filter using coupled butterfly-spiral shaped resonator for communication systems applications
    2011
  90. design and fabrication of microstrip dual - band bandpass filter
    2011
  91. simulation based organic thin film transistor (OTFT) modeling with artificial neural network
    2011
  92. modeling and simulation of turbogenerator using computational intelligence
    Kaveh Darabi 2010
  93. design simulation and fabrication of microstrip lowpass filter using modified half-circular patch resonators
    2010
  94. microstrip low-pass filter tapered resonator microwave monolithic integrated circuits (MMIC) lumped element step-impedance elleptic function passive element
    ALI LOTFI 2010
  95. modeling and simulation of silicon nanowire FET using neural network
    Jalal Rostamimonfared 2010
  96. Modeling of power LDMOS Transistors Using Artiical Neural Networks
    2010
  97. Extraction of PHEMT Small Signal Intrinsic Parameters Using Neural Network
    Baharak Akhlaghi 2009
  98. Simulation of Recycle Gas Compressor by Computational Lnteligence
    Seyed Mohammad Jamshidi 2009
  99. Submicron CMOS integerated circuits Design using neural network
    2009
  100. Nonlinear System Analysis by Fuzzy Method
    2009
  101. Simulation of DG MOSFET with the Computational Intelligence : Application to the simulation of the nanoscale CMOS circuit
    2009
  102. Visual 2-D Object recognition Using Artificial Neural Networks Based on feature extraction
    2009
  103. Predication of Microwave Transistor Noise parameters Using Neural Networks
    2009
  104. Heat Ttransfer Analysis Based on Application of Neural Network
    2007
  105. Analysis and proposed method for improvementof the MPEG-1 Layer III Audio encoder Algorithm
    MOHAMMAD BEHRAFTAR 2007
  106. Image compression
    2005
  107. Design of high frequency CMOS analog continuous time low pass filter
    2003
  108. Channel Assignment with Neural Network
    ELHAM HOSSEINI 2002

Update: 2026-11-18

افراد توان خواه
رنگ متن
رنگ پس زمینه
اندازه فونت
+ A -
پنهان سازی تصاویر
تنظیم کنتراست
فاصله بین کلمات
خط راهنما
فاصله بین خطوط
نوع فونت
بزرگنمایی انداره صفحه
+ -
توقف انیمیشن ها