profile - دانشکده فنی

 دانشکده فنی و مهندسی 

 پردیس دانشگاه رازی 
Maysam Saidi

Maysam Saidi

Associate Professor / Engineering / Dept. of Mechanical Engineering_test

Master Theses

  1. Numerical analysis of heat transfer in open microchannel heat sink with nature based fin geometries
    LeilaSadat Naderifard 2026
       Effective thermal management of high heat flux electronic chips and equipment is crucial for maintaining their performance and reliability. In this context, open microchannel heat sinks are highly significant as a modern thermal management approach, owing to their favorable heat transfer capacity and potential for reduced manufacturing costs. This study presents a 3D numerical investigation into fluid flow and heat transfer within a copper open microchannel heat sink, using water as the working fluid under laminar flow conditions. A uniform heat flux is applied to the bottom surface of the heat sink, and symmetry boundary conditions are imposed on the side walls. Numerical simulations are performed using ANSYS Fluent software based on the finite volume method. The study aims to introduce novel open microchannel heat sink designs and examine the impact of the structure and arrangement of nine distinct biomimetic leaf-i  ired fins. It specifically evaluates how the increased heat transfer surface area achieved while reducing volume compared to a baseline rectangular fin geometry influences heat transfer performance and pressure drop. The fin configurations are i  ired by tree leaves and are modeled based on the positive curvature section of an airfoil, scaled up in size. The results demonstrate that the fin geometry can significantly alter both the fluid temperature and the extent of fluid heating without changing the boundary conditions. In geometries featuring sequential and inclined fins, the flow is gradually diverted; compared to rectangular fins, this results in less abrupt path alteration and reduced flow contraction and expansion. Furthermore, the change in flow direction by generating transverse components and enhancing mixing thins the thermal boundary layer and boosts heat transfer. Regarding the average base temperature, the Cycas leaf fin geometry demonstrates the best performance, reducing the average base temperature by approximately 1.004% compared to the rectangular fin geometry, while the Cactus leaf fin geometry also shows favorable thermal performance with a reduction of about 0.49%. The Cycas leaf fin geometry exhibits a reduction of approximately 1.12% in maximum base temperature compared to the rectangular fin geometry, marking it as the best performer for peak temperature control; similarly, the Cactus leaf fin geometry performs well in controlling hotspots, achieving a reduction of about 0.47% in maximum base temperature. Among the geometries studied, the Cycas leaf fin geometry yields the lowest Theta value indicating superior base temperature uniformity with a value approximately 46.4% lower than that of the rectangular fin geometry. The Cactus leaf fin geometry also shows a 28.6% reduction in Theta compared to the rectangular fin geometry, demonstrating its effectiveness in maintaining base temperature uniformity. The eucalyptus-leaf and Type II monstera-leaf fin geometries exhibit low pressure drop but show poorer thermal performance regarding base temperature compared to the rectangular fin geometry; in contrast, the Type I monstera-leaf fin geometry simultaneously yields the lowest pressure drop and the highest Nusselt number and average convective heat transfer coefficient.
  2. Investigation of the behavior of a steel frame with an eccentric lateral bracing system using a link with a tubular cross-section of variable diameter.
    Hossein Azizpourian 2026
  3. The Effect of Thickness and Type of Coating of MGO Panels on Their Fireproof Performance
    Farshad Ghomami 2026
      Magnesium oxide panels have been considered as one of the mineral materials used in dry construction, partition walls, interior coatings and fire protection systems. However, the thermal performance, moisture resistance and mechanical stability of these panels depend on characteristics such as thickness, type of coating, thermal conditions and humidity level. The present study aimed to investigate the effect of thickness and type of coating on fireproof performance, moisture resistance and mechanical properties of magnesium oxide panels. This study is applied in terms of its purpose and experimental-descriptive in terms of its implementation method. MgO panel samples with different thicknesses, depending on the type of test, were investigated in the range of 8 to 16 mm. The tests included evaluation of thermal and non-combustible behavior, density, water permeability, environmental durability cycles, compressive strength, flexural strength and soft and hard impact tests.   The compressive strength of the samples was investigated at ambient temperature and after exposure to temperatures of 600 and 1200 °C. Also, the flexural strength was evaluated under ambient conditions, high temperatures and relative humidities of 50 and 100%. In addition, the effect of cold traffic coating on moisture behavior and the effect of expanding fireproof coating on thermal stability of the panels were studied. The results showed that increasing the thickness was accompanied by an increase in compressive strength, flexural strength and capacity recorded in impact tests. The 16 mm sample showed the highest initial strength and the highest residual strength after thermal exposure in most tests. The temperature of 600 °C caused a limited decrease in compressive and flexural strength; while at 1200 °C, the decrease in strengths became more severe.   The loss of compressive strength at 1200°C was about 55%, and the loss of flexural strength ranged from 38.44 to 60%, depending on the thickness of the sample. Humidity also caused a limited decrease in flexural strength; the intensity of the effect of saturated humidity was greater than that of average humidity, but much less than that of very high heat. The results of the intumescent coating test showed that this coating, when directly exposed to 1200°C, created an effective thermal protective layer on the panel surface. The coated samples did not experience significant extensive cracking, delamination, or delamination, and the thermal effects did not extend to the middle layers and core of the panel. Also, the mechanical strengths of the coated samples did not show a significant decrease after heating. Overall, increasing the thickness improved the mechanical capacity and thermal stability of the MgO panels, and the intumescent coating was also effective in reducing heat penetration and maintaining the structural integrity of the panel.   However, generalizing the results to all MgO products and determining the fire resistance class requires additional tests and evaluation of the entire system, including panels, cladding, substructure and connections.
  4. Smart load management for enhancing grid stability
    AHMED SALIH MOHAMMED 2026
    Cardiovascular diseases are one of the leading global causes of mortality, and rapid diagnostic modalities would be invaluable for determining pre-clinical signs. While the ECG is the main non-invasive tool for arrhythmia diagnosis, many automated ECG analysis systems are based purely on one-dimensional signal processing algorithms and therefore often fails in relation to diagnosing complex morphological variations. Prior work often divides signal and image space and neglects the inherent use of visual morphology by clinicians. To fill this void, the presented thesis proposes a new dual-domain framework for QRS-complex detection and heart-beat >  It is based on data available until October 2023 and uses the MIT-BIH Arrhythmia Database, aggregating heartbeats into two main clusters (normal and abnormal >  The QRS detection part obtained a very good sensitivity (99.90%), a positive predictivity of 98.99%, and an error rate value of only 1.12 %. Results: The signal-only model outperformed the >  
  5. AI Based distribution network state estimation
    NOORULDEEN HASHIM KAREEM 2026
    State estimation is a fundamental task in the monitoring and operation of electric power distribution networks, where accuracy and speed play a crucial role in maintaining real-time situational awareness of the grid. This thesis presents the development and evaluation of a multi-area, data-driven framework for distribution network state estimation. In the proposed framework, the network is partitioned into five areas; following feature engineering based on mutual information, various models—including Linear Regression, Lasso, ElasticNet, Multilayer Perceptron (MLP), and an Ensemble model—were employed to estimate voltage magnitude and phase angle. The method's performance was evaluated using standard 33-bus and 69-bus networks, utilizing metrics such as Mean Absolute Error (MAE), Root Mean Square Error (RMSE), and Maximum Error (MaxError). The results demonstrated that the regression models achieved voltage estimation accuracy comparable to the MLP, while their training times remained under 2.5 seconds for both networks; in contrast, training the MLP required approximately 45.2 seconds for the 69-bus network and 47.1 seconds for the 33-bus network. Under conditions of full observability, the ensemble model achieved a maximum error of 0.309% for voltage and 0.1337 degrees for phase angle in the 69-bus network. Corresponding values ??for the 33-bus network were 0.406% and 0.2294 degrees, respectively. Compared to the reference study [53], which reported a maximum voltage error of 0.30% and a phase angle error of 0.34°, the proposed method performed comparably in terms of voltage error and superiorly in terms of phase angle estimation for the 69-bus network; for the 33-bus network, although the voltage error was higher, the phase angle error remained lower than the reference value. Furthermore, the multi-area structure in the 69-bus network reduced the total training time from 153.94 to 117.71 seconds—a reduction of 23.5%. The study's primary innovation lies in presenting and evaluating an integrated framework comprising multi-area estimation, mutual information-based feature engineering, simultaneous comparison of regression and neural network models, and their combination into an ensemble model; this approach enables the simultaneous assessment of accuracy, computational cost, and robustness against measurement loss. Keywords: State estimation, distribution network, artificial intelligence, ensemble model.   
  6. Investigation of mechanical and fatigue properties of Warm mix Asphalt with bitumen modified with recycled vegetable oil
    GHADEER HUSSEIN NAHI 2026
         In this study, the effect of adding recycled vegetable oil on the mechanical properties and fatigue performance of half a gram asphalt has been investigated. For this purpose, the base bitumen was modified with different amounts of recycled vegetable oil including 2, 4, 6, 8 and 10 wt% and the made asphalt samples were subjected to softness, ductility, Marshall and compressive strength tests. The results showed that the addition of vegetable oil significantlyAttention reduces the softness point of bitumen, which indicates a reduction in mixing temperature and density and the realization of the goal of half-gram asphalt. On the other hand, ductility was maintained up to the threshold of 4% oil at its maximum value (100 cm), but it dropped sharply in the higher percentages and reached zero in the 10% sample, indicating the rupture of the colloidal structure and the clotting of the asphaltenes. Marshall's experiment showed that the maximum stability was related to the 2% sample with a   value of 11.21 kN, but this sample suffered a decrease in compressive strength. In contrast, the 4% sample with a stability of 7.90 kN and a compressive strength of 2.97 MPa (with a slight difference from the control sample) provided the best balance between bearing strength, adhesion and flexibility   He did. In contrast, samples containing 6% and above with a severe drop in Marshall stability (at 8% to less than 1 kN) and a significant reduction in ductility were practically unqualified for pavement applications. Finally, by combining all performance criteria, the amount of 4 wt% of recycled vegetable oil is introduced as the optimal percentage, which while reducing the production temperature to about 15 degrees Celsius, has the highest compatibility with maintaining It has adhesion properties and desirable potential to absorb fatigue strains and can be recommended as an operational option for bitumen modification in semi-gram pavements. In this study, the effect of adding recycled vegetable oil on the mechanical properties and fatigue performance of half a gram asphalt has been investigated. For this purpose, the base bitumen was modified with different amounts of recycled vegetable oil including 2, 4, 6, 8 and 10 wt% and the made asphalt samples were subjected to softness, ductility, Marshall and compressive strength tests. The results showed that the addition of vegetable oil significantlyAttention reduces the softness point of bitumen, which indicates a reduction in mixing temperature and density and the realization of the goal of half-gram asphalt. On the other hand, ductility was maintained up to the threshold of 4% oil at its maximum value (100 cm), but it dropped sharply in the higher percentages and reached zero in the 10% sample, indicating the rupture of the colloidal structure and the clotting of the asphaltenes. Marshall's experiment showed that the maximum stability was related to the 2% sample with a   value of 11.21 kN, but this sample suffered a decrease in compressive strength. In contrast, the 4% sample with a stability of 7.90 kN and a compressive strength of 2.97 MPa (with a slight difference from the control sample) provided the best balance between bearing strength, adhesion and flexibility   He did. In contrast, samples containing 6% and above with a severe drop in Marshall stability (at 8% to less than 1 kN) and a significant reduction in ductility were practically unqualified for pavement applications. Finally, by combining all performance criteria, the amount of 4 wt% of recycled vegetable oil is introduced as the optimal percentage, which while reducing the production temperature to about 15 degrees Celsius, has the highest compatibility with maintaining It has adhesion properties and desirable potential to absorb fatigue strains and can be recommended as an operational option for bitumen modification in semi-gram pavements.
  7. An Investigation of Behavior of Carbidic Austempered Ductile Iron with Dual Matrix Structure under Tensile Test
    Ali Olfati cheghagolani 2026
  8. Accuracy Evaluation of Approximate Performance Point Determination Methods Using Pushover analysis
    Mehdi Amini 2026
       Nowadays nonlinear analysis methods are employed for the seismic evaluation and strengthening of various structural systems. Detailed investigation of the actual performance of buildings during earthquakes and the development of economically optimized designs clearly demonstrate the necessity of performing nonlinear analyses. In performance-based seismic design, structures are designed to achieve different expected performance levels corresponding to different seismic hazard levels. One of the most important steps in performance-based seismic design is the determination and calculation of the performance point. To evaluate the structural performance, nonlinear analyses can be utilized, which are generally >Accordingly, various approximate methods for determining the structural performance have been proposed in seismic codes and guidelines. Among these methods are the Displacement Coefficient Method, the Capacity Spectrum Method, and the Improved Capacity Spectrum Method (N2 method). The objective of this study is to evaluate the accuracy of these methods in estimating the performance point. For this purpose, several reinforced concrete building frames are modeled, and their performance points are calculated using the aforementioned methods. To assess the accuracy of the results obtained from these methods, nonlinear time history analyses are performed on the same frames. The results of the nonlinear time history analyses are considered as reference (exact) results and are used as a basis for evaluating the level of approximation and accuracy of the Displacement Coefficient Method, the Capacity Spectrum Method, and the Improved Capacity Spectrum (N2) Method.          Keywords: Performance Point, Nonlinear Static Analysis, Capacity Spectrum, N2 Method
  9. Three-Dimensional Investigation of Stone Column Efficiency on Slopes with Different Geometric Arrangements
    Mersad Babaee Rad 2026
    در اين پژوهش، عملكرد ستون‌هاي سنگي به عنوان روشي موثر در تقويت خاك‌ها و افزايش پايداري شيب‌ها مورد بررسي قرار گرفته است. هدف اصلي تحقيق، تحليل سه‌بعدي راندمان ستون‌هاي سنگي با توجه به آرايش‌هاي هندسي مختلف در شيب‌هاي مختلف مي‌باشد. بهسازي و تقويت شيرواني‌هاي خاكي در برابر تغييرمكان‌هاي جانبي، نشست و كاهش ضريب اطمينان از موضوعات مهم در مهندسي ژئوتكنيك است. ستون‌هاي سنگي به‌عنوان يكي از كارآمدترين روش‌هاي بهسازي زمين، با ايجاد محصورشدگي جانبي، بهبود زهكشي و افزايش سختي توده خاك، نقشي مؤثر در افزايش پايداري شيرواني‌ها ايفا مي‌كنند. با وجود اين، كارايي ستون‌هاي سنگي تا حد زيادي به آرايش هندسي، طول ستون، قطر و نحوه اندركنش آن‌ها با لايه‌هاي خاكي وابسته است. در اين پژوهش، عملكرد سه آرايش هندسي ستون‌هاي سنگي (مثلثي، مربعي و شش‌ضلعي) و همچنين تأثير طول ستون، به‌صورت عددي و سه‌بعدي با استفاده از نرم‌افزار PLAXIS-3D   مورد بررسي قرار گرفته است. نتايج نشان داد كه آرايش‌هاي هندسي مختلف اثر قابل توجهي بر رفتار مكانيكي شيب دارند. آرايش مثلثي بهترين عملكرد را از نظر كاهش جابه‌جايي افقي و افزايش ضريب اطمينان پايداري ارائه كرد؛ به‌طوري‌كه بيشترين مقدار ضريب اطمينان برابر با 6/1 براي اين آرايش به‌دست آمد. در مقابل، آرايش شش‌ضلعي ضعيف‌ترين عملكرد را داشته و كمترين ضريب اطمينان برابر با   28/1 ثبت شد. اين اختلاف بيانگر بهبود حدود 25 درصدي ضريب اطمينان در آرايش مثلثي نسبت به شش‌ضلعي است. بررسي تأثير طول ستون نيز نشان داد كه افزايش طول ستون از 3 متر به 6 متر موجب افزايش حدود 2/21 درصدي ضريب اطمينان پايداري شيب مي‌شود. همچنين با افزايش طول ستون، جابه‌جايي افقي به‌طور معني‌داري كاهش يافته و رفتار شيب پايدارتر شده است. از نظر تنش‌ها نيز مشاهده شد كه آرايش مثلثي بالاترين مقدار تنش برشي پيك را در حدود 390 كيلوپاسكال ايجاد مي‌كند، در حالي‌كه آرايش مربعي مقدار مياني حدود 350 كيلوپاسكال و آرايش شش‌ضلعي كمترين مقدار را نشان داد كه ناشي از محصورشدگي جانبي كمتر است. به‌طور كلي، نتايج تحقيق نشان داد كه انتخاب آرايش مناسب ستون‌هاي سنگي و بهينه‌سازي طول آن‌ها مي‌تواند كاهش قابل توجهي در نشست قائم، جابه‌جايي جانبي و افزايش چشمگيري در ايمني شيب ايجاد كند. يافته‌هاي اين پژوهش مي‌تواند به‌عنوان مرجعي براي طراحي بهينه ستون‌هاي سنگي در پروژه‌هاي عمراني به‌ويژه در شرايط خاك‌هاي سست و لايه‌اي مورد استفاده قرار گيرد.   
  10. طراحي و شبيه سازي پيشرفته بيوسنسورهاي مبتني بر ترانزيستور گيت كوتاه: بررسي اثر ضريب دي الكتريك بر عملكرد سنسور
    Zahra Bayat 2026
  11. Investigation of the Effect of Fe/Al organic framework particles on Mechanical Properties and Corrosion of Unsaturated Polyester Resin.
    Zeinab Khodamoradi 2025
    Unsaturated polyester resin (UPR) is widely used in the composite industry due to its desirable properties such as low cost and good processability. However, its low corrosion resistance, high brittleness, and flammability limit its applications in various industrial fields. To overcome these limitations, the incorporation of reinforcing particles into the resin has recently been proposed as an effective approach. In this study, bimetallic metal–organic frameworks (Fe/Al-BDC-NH?) were employed as reinforcing additives to investigate their effect on the physical–mechanical properties and corrosion resistance of unsaturated polyester resin. Owing to their hybrid structure, the MOF particles—with metallic sites enhancing mechanical performance and organic linkers enabling interfacial bonding with polymer chains—prevented particle sedimentation and improved the uniformity and adhesion of the polymer network. Structural and performance analyses of the composites were carried out using XRD, FT-IR, FE-SEM, DMA, and electrochemical impedance spectroscopy (EIS). The results revealed that the incorporation of a small amount of Fe/Al-MOF significantly increased the storage modulus, improved interfacial adhesion, enhanced electrochemical stability, and reduced the permeability of the resin in corrosive environments. Overall, the presence of bimetallic MOF particles remarkably improved the mechanical and anti-corrosion performance of the unsaturated polyester resin and offers a promising route for developing high-performance, corrosion-resistant coatings and composites for industrial applications.   
  12. تشخيص خودكار عدم تمركز راننده با استفاده از بينايي ماشين و يادگيري عميق
    Samira Karimichaghakabodi 2025
  13. Numerical analysis of counterflow jet effect in a blunt body on drag force and temperature in hypersonic flow
    MAHDI YAVARI 2025
  14. Numerical analysis of flow and heat transfer in a heat sink with porous metal foam under impingement flow
    Moein Safari ghale 2025
    Abstract
  15. Numerical Simulation of Door Opening Effect on the Flow Field and Particle Distribution in a Cleanroom
    Sadegh Raji 2025
  16. evaluation of seismic performance of Reinforced Concrete frames equipped with friction and yielding damper with low yield point steel (LYP160)
    Mona Mahdavian 2024
  17. Numerical analysis of gas-solid flow in a rectangular spouted fluidized bed with pulsed inlet flow using MFIX-DEM
    Pedram Ghaderi dehrash 2024
       In recent years, fluidized beds have garnered attention across various industries due to their advantageous characteristics, such as uniform temperature distribution, effective phase mixing, and high heat transfer rates. One effective method to enhance the efficiency of these beds is the use of a pulsed inlet. This technique improves the homogeneity of the bed and eliminates inactive and stagnant zones (dead zones) within the particles by varying the inlet air flow. Despite extensive research on the simulation of conventional fluidized beds, the study of pulsed bed systems has been relatively limited. In this thesis, the gas-particle two-phase flow in a spouted fluidized bed with a rectangular geometry and pulsed air inflow was numerically investigated. The simulation was carried out using a combination of Computational Fluid Dynamics (CFD) and the Discrete Element Method (DEM). To reduce computational costs, the geometry was defined as quasi-two-dimensional with a depth of 6 particles. The modeling was performed in a transient state, where a specific number of particles were initially placed at a certain height within the bed, and then gas was injected into the bed at a specified pulsed velocity. In this study, the pulses were applied in three waveforms: square, sinusoidal, and sawtooth, with frequencies of 1, 4, and 10 Hz. The results showed that when fluidizing (side) gases were present in the bed, applying a pulsed inlet in the spout positively impacted the elimination of dead zones and the circulation of particles across all three frequencies and waveforms. It was demonstrated that a frequency of 10 Hz and a square waveform yielded the best results. For instance, in a spouted fluidized bed at 10 Hz, the particle travel distance improved by 12.81%, 5.99%, and 5.97% for square, sinusoidal, and sawtooth waveforms, respectively. Similarly, improvements of 55%, 35%, and 30% were observed in the reduction of dead zones. In rectangular beds, it was found that the removal of fluidizing gases had significant negative effects on particle circulation and increased the dead zones, with the proportion of dead zones rising from 0.5% to 7.7% of the total particles. Finally, to examine the effect of fluidizing gases, different configurations with varying spout and fluidizing gas velocities were investigated. In these configurations, the spout velocity was gradually decreased while simultaneously increasing the fluidizing gas velocity, keeping the total inlet gas flow constant. The results showed that in two configurations where the fluidizing gas velocity reached its maximum, the dead zones were completely eliminated, particle mixing improved, and homogeneity in particle distribution increased. In the optimal gas inlet configuration, applying a square pulsed inlet at 10 Hz resulted in a 1.55% improvement in the average particle travel distance. In this study, it was demonstrated that by applying a pulsed flow and adjusting the inlet gas velocities, the hydrodynamic performance of the bed can be improved without the need for changes in the system geometry or the total inlet flow rate.
  18. Numerical analysis of gas-solid flow erosion in different geometrical fittings as alternatives to a standard pipe elbow
    Ahmadreza Veyskarami 2024
    در بسياري از صنايع مهندسي ذرات جامدي كه همراه سيالات حمل مي¬شوند، توانايي آسيب سايش به خطوط لوله و خصوصاً اتصالات را دارند و آن¬ها را در معرض نشت و شكست قرار مي¬دهند. در واقع سايش يك مكانيسم مكانيكي است كه سبب جداشدن مواد از سطح به دليل برخورد مكرر ذرات جامد است و خسارت¬هاي مالي و جاني در پي دارد. به همين سبب باعث شده است كه اين موضوع اهميت پيدا كند و روش¬هايي در جهت كنترل سايش پيشنهاد شود. يك روش مناسب براي پيش¬بيني نرخ سايش حل ديناميك سيالات محاسباتي است كه در سال 1990 امكان استفاده از اين روش فراهم شد. پژوهش حاضر سعي در استفاده از رويكرد اويلر - لاگرانژ با نرم‌افزار انسيس فلوئنت دارد بدين منظور كه شبيه‌سازي جريان سيال (فاز پيوسته) در ديدگاه اويلري و شبيه‌سازي رديابي ذرات جامد (فاز گسسته) در ديدگاه لاگرانژي صورت مي¬گيرند. در ادامه فرايند استقلال از شبكه و ذرات براي جريان دوفازي گاز - جامد در هندسه زانويي 90 درجه استاندارد انجام مي¬شود. همچنين اعتبارسنجي داده¬هاي عددي حاضر مساله با داده¬هاي تجربي ديگر مقالات تحت شرايط يكسان، براي جريان تك¬فاز و دوفاز مقايسه مي¬گردند تا نتايج قابل‌قبولي لحاظ گردد. در همين راستا سبب شد مدل آشفتگي از نوع تنش رينولدز، كوپل يك¬طرفه، مدل سايش اوكا، مدل ضريب بازگشت ذرات گرانت و تاباكف و نيروهاي وارده بر ذرات شامل پسا، جرم مجازي، شناوري و گرانش در حل عددي اين پايان‌نامه انتخاب شوند. پارامترهاي زيادي در ميزان سايش دخيل هستند كه در اين پژوهش برخي پارامترها شامل سرعت جريان، اندازه قطر ذرات، نرخ ورودي ذرات و تأثير زبري سطح ديواره مورد بررسي عددي قرار داده شدند. در بين اتصالات، زانويي¬ها در معرض خطر جدي¬تري هستند. با پيشنهاد جايگزيني اتصالات ديگر كه هدف و ماهيتي شبيه به كارايي زانويي دارند، انتخاب مي¬شوند و سايش را نسبت به زانويي 90 درجه استاندارد كاهش مي¬دهند. اتصالات شامل دو نوع خم مايتر، سه نوع اتصال كور، زانويي كاهنده و دو نوع زانويي كروي شكل هستند. شرايط حل عددي براي تمام اتصالات جهت مقايسه نتايج با يكديگر به¬صورت مشابه تنظيم مي¬گردند. سپس نتايج عددي نهايي پايان‌نامه بيان مي¬كند كه در سرعت جريان و قطر ذرات يكسان براي بحراني‌ترين حالت، اتصالات ذكر شده مقاومت سايشي را 22/5% تا 39/6% نسبت به زانويي 90 درجه استاندارد افزايش مي¬دهند.
  19. Design, simulation and fabrication of Wilkinson power divider using high impedance meandered lines and new structure to increase operating bandwidth
    Payman Fallahisepehr 2024
  20. The study of sensitivity analysis and gene expression modeling of natural gas density using thermodynamic properties without the need for gas analysis
    Saba Afroozi 2024
  21. The effect of annealing heat treatment in two-phase zone on the corrosion behavior of ductile cast iron.
    Zahra Jabari 2024
  22. Investigation of Stress Corrosion Cracking of Carbidic Austempered Ductile Iron
    SUMAYA JABBAR MUTAR 2024
    Developing the scope of application of new material depends on understanding the behavior of these in different environments and also gaining knowledge on the effect of various factors such as heat treatment parameters on their properties.   With regard to this issue we focused on the investigation the effect of partial austenitizing duration on creating a matrix with a dual structure of ferrite-ausferrite, corrosion resistance, bending strength, time to failure in crosive media under applied bending loads and stress corrosion threshold stress of a carbidic austempered ductile iron (CADI) which has been known as new family of ADI. In this regard, cast parts from a non-alloy carbidc cast iron were first subjected to ferritizing annealing to obtain full ferritic matrix. Then, the samples were partially austenitized at 870 ?C for 10, 15, and 20 minutes, followed by austempering in a molten salt bath at 350 ?C for one hour. After it, samples microstructures were examined with an optical microscope. In the next step, electrochemical corrosion tests were performed with Tafel polarization method. Then, by preparing notched and smooth C-ring samples, the loads leading to their failure were determined under the bending tests in air. Finally, the behavior of C-ring samples in corrosive caustic soda solution were investigated under bending loads. According to the obtained results, with the increase of the partial austenitizing time, the ausferrite phase fraction increased according to the JMAK equation. The creation of dual matrix structure of ferrite-ausferrite caused the corrosion resistance of the samples to be weakened compared to the samples with fully ferritic matrix and conventional ADI. As the partial austenitizing time increased, the corrosion resistance, bending tensile strength in air and time to failure in corrosive media under constant load, increased. The bending loads leading to the failure of notched samples in air were significantly lower than those of smooth samples. The results of stress analysis in C-ring samples under bending test in air showed that the reduction of cross-sectional area, change the outer effective radius and neutral radius of the samples, and stress concentration are three contributing factors in reducing the tolerable bending load without occouranse failure with the contribution of 35%, 35% and 30%, respectively. The notch strength ratio (NSR) was independent of the effect of partial austenitizing time and it was about 0.87. All the smooth samples endured 100 hours of stress-corrosion testing under maximum applied loads (equivalent to 85% of failure load in air) without occurrence of failure. By decreasing the applied load in the corrosive environment, the time to failure of all samples increased greatly. There was a power relationship between the stress-corrosion threshold stress and the ultimate tensile strength of the samples. Also, during stress-corrosion testing the gradual fracture along with growth of cracks was not observed and failure of all samples in both environments air and caustic soda occurred via very rapid crack propagation in a completely brittle mode over the whole range of the applied loads.   
  23. Numerical investigation of fault rupture deviation using a barrier wall filled with plastic waste
    Hanyeh Mirabasi nia 2024
  24. Transient liquid phase (TLP) bonding to repair compressor blades of Ilam Gas Refinery
    Arian Piri 2023
  25. Simulation, design and construction of Wilkinson power divider using low pass filter, PSO based optimization and analysis
    Milad Mohammadi 2023
  26. Design, simulation and construction of Wilkinson power divider based on the optimization of neural networks and the use of a trapezoidal resonator.
    Hesam Qytasy sarabi 2023
  27. Design, Simulation and fabrication of compact Wilkinson power divider with harmonics suppression using combination of Chebyshev and modified elliptic structure
    Mina Saran 2023
      In
  28. Experimental study of the bubble formation regimes in gas-liquid two-phase flow in a vertical pipe
    Elahe Shafiee 2023
       Identification of two-phase flows and its Taylor bubble characteristics is one of the most important parameters designing industrial installations for intermittent gas-liquid two-phase flow. Also, it is important to know the characteristics of two-phase flow in order to improve the exploitation of oil wells and to optimize the process of maintenance and repair of flow transmission lines with the purpose of cleaning pipelines along with reducing its costs in the oil and gas industries and in chemical and electronic chip cooling industry. The purpose of this research to analyze bubble flow patterns, achieve two-phase flow patterns of water and air using numerous experimental tests and investigate the effect of pulsating gas flow on the characteristics of the Taylor flow field (Taylor bubble length and velocity) under different two-phase inlet conditions air and water done in the form of an upward parallel flow. The range of studied apparent velocity Gas and Liquid phase is 0.12-0.28 m/s and 0.05-0.25 m/s, respectively, and the pulsating gas flow frequency is 0.25-0.4 Hz. In this study, by examining more than 100 different apparent velocities for the phases, three patterns of bubble, slug and churn were observed and a map of the two-phase flow pattern of water and air was drawn. Also, the effect of pulsating gas flow on the length of the Taylor bubble was investigated in 150 different experiments, and the results of this study showed that with the increase of the pulsating gas flow and the frequency, the stability of the Taylor bubble flow increased and the length of the Taylor bubble decreased significantly. So that at the frequencies of 0.25, 0.5, 1, 2 and 4 Hz, respectively, the maximum bubble length was observed at the liquid velocity of 0.12 m/s and gas velocity of 0.25 m/s are 455.5, 367, 313.1, 286.3 and 244.2 mm.   Also, at a constant frequency, the length of the Taylor bubble increases with the increase of the apparent velocity of the gas phase. For example, at a constant frequency of 1 Hz and a liquid velocity of 0.12 m/s, the bubble length increased from 147.8 mm to 1.313 mm when the gas velocity increased from 0.10 to 0.25 m/s. In addition, in this research, with the help of image processing, the movement speed of the Taylor bubble was measured and determined for 15 different apparent speeds using the speed measurement technique. Comparison of the obtained linear equation with previous studies showed that the relationship has a good fitting accuracy. The results of the present work proves that the pulsating gas flow technique enables the control of the gas-liquid Taylor bubble flow pattern and the stability of the motion of the Taylor bubbles, which will be very useful for future industrial applications in gas-liquid reactions.
  29. Numerical study of mixing characteristics in a rectangular spout–fluid bed using Discrete Phase Model
    Mohammad Karimizand 2023
  30. Numerical Analysis of Spiral Blades Effect on Erosion of a 90-Degree Elbow
    Abbas Ahmadi 2023
    Abstract: Due to the limitations of mineral resources on the earth and the distant horizon for long-term life on this planet, preservation and maintenance of materials against damage and destruction becomes very important in industrial societies. On the other hand, the growing process of industrialization of human life has increased the share of industrial sectors in the financial portfolio of governments, and governments are forced to send a large amount of their financial resources to the industrial market every year in order to reach the desired level of industry. Abrasion is one of the main destructive events in the fluid transfer sector in industries. Especially when two-phase and multi-phase fluid flows are involved. Obviously, the countries where the transfer of refinery, power plant, oil and gas fluids is considered their vital artery are more involved in this phenomenon in their industries than others. Today, software simulations compete strongly with laboratory research. Because laboratory research, despite all its inherent advantages and advantages, has disadvantages such as high costs. On the other hand, the increasing power of computer systems for analysis and simulation is a powerful support. This research is a simulation with the help of numerical methods, in which a 90 degree elbow is considered as a sample piece (which is one of the most damaged industrial connections). To carry out the desired simulation, a computational fluid dynamic model has been used along with the discrete cell method. The continuous fluid and the particles injected into the flow at the elbow inlet were simulated in different geometries. The final simulation model includes McLaury's Erosion model based on the validation results. Particles are tracked by Lagrangian method along with random collisions of Grant-Tabakoff recursive model. To ensure the correctness of this choice, another validation has been used in this section. Considering that particle momentum plays an important role in Erosion, in this research, it has been tried to make the injected particles lose their momentum by rotating the water flow lines. Therefore, changes were made in the same direction in the knee geometry. The result of this research shows that changing the geometry of the elbow reduces the momentum of the particles when they collide with the internal surfaces to the extent that it increases the life of the elbow by about 8 times in the case of using internal spiral blades. Key word: Erosion, elbow, helical blades, computational fluid dynamics, Euler Lagrange, particle tracking   
  31. Numerical Study of Airflow Containing Airborne Particles in the Human Respiratory System Based on Medical Images
    Saba Khaksar 2023
    بيماري‌هاي ريه داراي آمار بالاي مرگ و مير در جهان هستند. دراين‌ميان آسم به عنوان شايع‌ترين بيماري شناخته‌مي‌شود و طبق گزارشات در سال ???? بيش از ?? ميليون نفر در آمريكا مبتلا به آسم بوده‌اند. بسياري از روش‌هاي درماني بيماري‌هاي ريوي و همچنين برخي بيماري‌ها، استنشاقي مي‌باشند، بنابراين شناخت رفتار ذرات استنشاقي (آلودگي‌ها و ذرات دارويي) همراه هوا درون مجاري تنفسي امري ضروري است. در مطالعه حاضر چهار نسل از ريه يك خانم ?? ساله سالم و غير سيگاري از تصاوير پزشكي سي تي اسكن استخراج شد. هندسه به 7 ناحيه تقسيم شد، سپس توسط شبكه بي‌سازمان با روش هموارسازي و با سلول‌هاي چندوجهي جهت حل عددي شبكه‌بندي گرديد. جهت شبكه‌بندي، ابتدا هندسه وارد محيط نرم‌افزار اسپيس‌كليم شده و در آن‌جا يكپارچه‌سازي هندسه انجام شد. سپس با استفاده از قابليت توپولوژي مجازي محيط انسيس مشينگ ، صفحات انتخاب شده و با گزينه تركيب سلول، تلفيق صفحات جهت ورود به محيط فلوئنت مشينگ انجام‌شد. سپس به وسيله استقلال حل از شبكه، شبكه مناسب انتخاب شد. از مدل آشفتگي k-?   براي شبيه‌سازي جريان آرام تا آشفته استفاده‌گرديد. ذرات با ديدگاه لاگرانژي و با استفاده از مدل فاز گسسته به ناحيه محاسباتي تزريق شد و مسيريابي و مدل‌سازي الگوي نشست در نواحي مختلف انجام شد. بر روي ساختار جريان در مجاري تنفسي براي نرخ‌هاي جريان مختلف و اثرات پديده‌هاي مختلف به‌وجودآمده در اين مجاري بر روي نشست ذرات بحث گرديد. الگوي نشست ذرات براي نرخ‌هاي مختلف جريان، به صورت منطقه‌اي و كلي به‌دست‌آمد و اثر نرخ جريان، اندازه و شكل ذرات بر ميزان نشست بررسي شد و در نهايت با استفاده از بهينه‌سازي و بهره‌گيري از روش پاسخ سطح و الگوريتم ژنتيك، حالت بهينه براي كمينه و بيشينه نشست ذرات در ناحيه درخت برونش به‌دست‌آمد. راندمان نشست بر حسب پارامتر برخورد نشان داد كه در تمامي نواحي مدل از جمله دهان- گلو، ناي و درخت برونشي، برخورد اينرسي نقش مهمي در نشست ذرات دارد. تحليل ساختار جريان سيال در مدل هندسه نشان داد كه جريان برگشتي، تشكيل گردابه و جت حنجره همگي بر ساختار جريان هوا و الگوي نشست ذرات اثرگذار هستند. ناحيه دهان-گلو داراي بيشترين كسر نشست به ازاي نرخ‌هاي جريان مختلف است. نتايج نشان داد كه تزريق به دو صورت تك ذره و استفاده از تابع توزيع بر ميزان نشست ذرات اثرگذار است. همچنين افزايش قطر ذرات باعث تغيير الگوي نشست ذرات شده و كسر نشست در ناحيه دهان-گلو افزايش يافت و شكل ذرات با اثرگذاري بر روي ضريب پسا، موجب تغيير الگوي نشست ذرات گرديد. از جمله نتايج ديگر اين بود كه بيشترين كسر نشست مربوط به ذرات كروي است. بررسي همزمان اثر قطر، شكل ذرات و سرعت ذرات و آناليز حساسيت نشان داد كه قطر با تاثير 60%، موثرترين پارامتر بر ميزان نشست ذرات است و پس از آن، ضريب شكل و سرعت قرار مي‌گيرند. در نهايت پيش‌بيني الگوريتم ژنتيك، بيشينه نشست ذرات در ناحيه درخت برونش را، 17% گزارش‌كرد، درحالي‌كه براساس نتايج عددي بيشينه نشست ذرات در ناحيه درخت برونش 20% گزارش شد. همچنين كمينه نشست ذرات توسط الگوريتم ژنتيك در ناحيه درخت برونش، 2/0 % گزارش گرديد، درحالي‌كه براساس نتايج عددي كمينه نشست ذرات در اين ناحيه، 24/0 % گزارش‌شد.   
  32. Numerical investigation of the geometrical parameters effects on the square cyclone separator performance
    Hooman Abdi Chaghakaboodi 2022
  33. Numerical simulation of gas_solid flow in a cyclone separator with aditional air inlet
    Shahla Noori 2022
      Separation of gas-solid flows is an important process in many industries. Cyclone separators are the most common devices for separating solid particles from gas flows, which indicates the importance of studying and researching to increase their efficiency and reduce energy consumption by reducing the pressure drop. In this regard, the present study used an additional inlet to enter flow into the cyclone with the aim of increasing the separation efficiency of a standard gas cyclone. To find the optimal height, this additional inlet was added at four different heights along the length of the cyclone, including the heights of 0.95D, 1.4D, 1.5D and 1.95D (D is the diameter of cylindrical section of cyclone) and the results were obtained for two conditions of inlet flow distributions: Increasing the inlet flowrate and division the inlet flowrate. In the first case, in addition to the polluted air flow entered through the original inlet (that was equal to the flowrate of cyclone without an additional inlet), an extra flowrate (20% of flowrate of original inlet) was injected through the additional inlet. In other words, the total flowrate of the cyclone was 20% more than it in cyclone without additional inlet. In second case, part of the inlet flow (83.33%) was injected through the original inlet and part of it (16.67%) was injected through the additional inlet, so the total inlet flowrate was equal to it in cyclone without additional inlet. The Reynold stress turbulence model (RSM) was used to solve the Averaged Navier- Stokes equations and Eulerian- Lagrangian approach and discrete phase model (DPM) was applied to track particles with a uniform diameter of 0.5 to 1.8 micron as discrete phase. The results showed that, in both flow distribution cases, installing the additional inlet at a height of 0.95D has the most positive effect on the separation efficiency. The separation efficiency increased 28.8% in flowrate increasing case and 19.6% in flowrate division case for particles with diameter of 0.5 micron compared to cyclone without additional inlet. In addition, in both of the flow distribution cases, increasing the separation efficiency of sub-micron particles was greater than it of bigger particles.
  34. Numerical study of the effect of variable curved shape fines height on fluid flow characteristics in open microchannel heat sink
    Ramtin Fattahi 2022
    Controlling the heat generated by electronicequipment and microelectromechanical systems at high capacities is importantfor optimal performance and greater reliability. Open microchannel heat sinksare a new geometry of microchannels heat sinks that are important due to theirlower manufacturing cost and better heat transfer performance. In this research, heat transferand fluid flow characteristics of open microchannel heat sink in 17 differentgeometries, which includes 3 main shape of rectangular fins, plano convex fins andplano concave fins, that variable fins base heights varied from 0.4-0.7 mm, andin 2 shape of plano convex fins and plano concave fins on the same variablecurve range coefficients 0.20-0.5 for plano convex fins shape and 0.35-08 Forplano concave fins shape   on an equal finsbase height which the convective surface area and the materials that arerequired to build a heat sink are equal have been investigated. Openmicrochannel heat sink cooled by water fluid in   a laminar flow and single phase flow   that Reynolds number varied from 100-600 andheat flux 100-600 kWm2   that numericallyand in a three-dimensional geometry analyzed by Ansys Fluent software. At thesame heat flux, Reynolds number and fins base height, the Nusselt number of therectangular fins shape is less than the two shapes of plano convex fins andplano concave fins.in Comparison of two shapes of plano convexfins and plano concave fins in the lower fins height, the Nusselt number of theplano concave is more than plano plano convex and in the higher fins height,the Nusselt number of the plano convex is more than the plano concave. Despite the fact that at high heightsin the fins, where the Nusselt number of the plano convex fins shape is greaterthan the rectangular and plano concave   shape,but the plano convex pressure drop is less than these two shaps. The results show that at the end of the path, where theheat sink temperature is higher, in the plano concave model due to the moreconvective surface area at the end of the path has a lower critical temperatureand temperature non-uniformity. Despite the higher Nusselt number in plano convex finsshape in the curve coefficient of 0.80, 0.65 and 0.50 Compared to other plano concavefins shape in curve range coefficients of 0.35 and0.20, have a lower pressure drop than the above shapes.  
  35. Medical Image-Based Numerical Study of Blood Flow in the Left Coronary Artery with Aneurysm
    Ashkan Rafiei 2021
      در پايان­نامه حاضر جريان پايا و گذراي خون در مدل
  36. Link prediction enhancement for location - based social networks using sentiment similarity
    Samira Basami 2019
      Abstract Social networks has attracted many users. These social networks have enabled user to connect to each other and share text, image and videos. A social network that allows users to share their location is named a location-based social network. Users can leave their tips on places they have visited and share it with others. User feedback is reflection of how they feel about the places they have visited. In social networks, people are connected to each other’s. One of the issues of these networks is the prediction of communication that may be created between two users in the future. Link prediction is the name chosen for this issue. There are many approaches used to predict links. Network structure information, user information such as their interests and characteristics, and location information that users have visited are used to predict links. User’s sentiment is one of the information that can be used to improve link prediction. Their tips can be analyzed to gain a sentiment for users in location-based social networks. This can provide a new algorithm for link prediction by combining the information of network structure, the information of the places they visited and their sentiments. The algorithm was tested on a foursquare network dataset, and it was found to perform better than one that does not use user sentiment. Therefore, it can be concluded that the role of sentiment is effective in creating new links among users. Keywords: social network, location-based social networks, link prediction, sentiment, location sharing
  37. ايجاد پوشش نانو كريستال نيكل -موليبدن و بررسي رفتار خوردگي فرسايشي
    Katayoon Zarian 2019
  38. Dry reforming of methane on Lanio3 in microchannel Reactor
    Atefeh Ghazi 2019
  39. surface water treatment for drinking water using membrane technology
    SEYEDEH SIMA MIRZADEH 2019
  40. Countinuesly prouducton of biodiesel from bacteria in the packed - bed reactor by using enzyme immobilization
    Mahsa Shahbande 2018
  41. DCAP.SDN (Dynamic controller allocation in software defined network)
    AHMAD REZA AHMADIAN 2018
  42. Dynamic behavior of pile group.................
    Adel Jalilian 2018
  43. Modeling of fuel cell performance by new machine learning methods
    Mehdi Allahdad 2017

Update: 2026-11-18

افراد توان خواه
رنگ متن
رنگ پس زمینه
اندازه فونت
+ A -
پنهان سازی تصاویر
تنظیم کنتراست
فاصله بین کلمات
خط راهنما
فاصله بین خطوط
نوع فونت
بزرگنمایی انداره صفحه
+ -
توقف انیمیشن ها